How To Set A Mole Trap

Download Article

Download Article

If you have a mole problem, Victor mole traps are an effective manner to kill them. The 2 main kinds of Victor mole traps are the Out O'Sight and Plunger-Manner mole traps. The Out O'Sight trap has a gear up of jaws or teeth, while the Plunger-Style has spring-loaded spikes that shoot into the basis. If yous observe an active mole tunnel and set the trap properly, you can become rid of the moles on your property.

1. 1

   Observe mole tunnels in your backyard. Look for mounds of dirt around your property, as this is a sign of a tunnel. Poke a hole through the mound with a stick or the end of a broom handle. If the pigsty is covered up 24 hours later, you tin can assume that it is an active mole tunnel.^[1]

   • If you have multiple mounds effectually your lawn, put a hole in each of them to observe all the agile tunnels.

2. 2

   Dig a hole in the top of an active tunnel. Selection a tunnel that's been covered by a mole, and dig a hole in the top of the tunnel with a spade. The pigsty should exist about 6 inches (15 cm) wide and penetrate down into the mole tunnel. Dig downwards into the tunnel and put the dirt to the side for subsequently.^[ii]

   Advertizement

3. 3

   Feel for the tunnel with your fingers. Stick your fingers into the hole you fabricated and feel effectually for the pathway to the mole tunnel underground. You should feel 2 holes on each end of the pigsty you but dug.^[three]

Advertising

1. ane

   Create a mound of dirt in the center of the hole. Use some of the dirt that yous dug up and place information technology back into the center of the hole until the top of the mound sits affluent with the ground. The mound should be centered in between the holes in the tunnel. The lesser pan or trigger on the bottom of your trap should residuum on the height of this dirt mound.^[4]

2. 2

   Place the setting levers over the springs. Thread the setting levers under the top of the handles on each side of the trap. And then, fit the setting levers over the springs in the middle of the trap and slide them upwards.^[5]

3. iii

   Push the levers together with the palms of your hands. You may have to use a proficient amount of force to open up the teeth of the trap. In one case both levers touch each other, your trap'south teeth should be fully opened.^[6]

4. iv

   Flip the safety latch over the acme of the trap. The prophylactic will exist a small metal clip on the acme of your trap. Flip it upwardly then that it catches on the other side of the clip and holds your trap open. Information technology's important to keep the safety latch engaged until the trap is completely set up up. You lot can now unthread the setting levers and set up them aside.^[7]

   • Grip both of the levers with one manus to go on them open while you set the safety.

5. 5

   Identify the end of the setting bar on the trigger pan. The trigger pan is a metal tab on the bottom of your trap, and is what the mole will press on to close the trap. The setting bar is the bar on the acme of the trap with a hooked finish. Hook the end of the setting bar onto the edge of the trigger pan. Make sure the prophylactic latch is yet engaged so that the trap doesn't close.^[8]

   • When the pan is pushed upwards, the setting bar will disengage and the trap will close shut.

6. 6

   Identify the trap around the dirt mound in the hole. Position the trap so that the teeth don't block the holes in the tunnel. The teeth of the trap should exist around the mound and fit around holes in the tunnel. One time the mole gets to the dirt mound, it will endeavor to dig through the mound, which will appoint the trap.^[9]

7. 7

   Release the safety on the height of the trap. Flip the safety over. If you gear up everything up correctly, the teeth of the trap should remain open up and slam shut when pressure level is practical to the bottom of the trigger pan.^[10]

   • Continue pets and children out of the yard when the mole trap is engaged.

Advertizing

1. 1

   Fill the hole up with loose dirt. If the dirt under the trap is as well compact, the spikes won't be able to penetrate into the basis fast enough to catch the mole. Suspension upwardly the soil that you dug upwardly so that it'southward loose before placing information technology back into the pigsty.

2. 2

   Press downwardly on an active mole tunnel with your thumb. Making a depression in the dirt will plummet the tunnel. This volition require the mole to couch through the obstructing dirt the side by side time it uses the tunnel, which will engage your trap.^[11]

3. iii

   Press the trap over the depression. Position the trap so that the side spikes don't block the tunnel below. The trigger pan is the metal square on the bottom of the trap, and should be positioned direct over the depression that you created in the clay. Press down on the trap so that the side spikes get into the ground and the trigger pan runs flush with the ground.^[12]

   • The trap latch is the metal rod attached to the top of the trap and should be in the downward position.

4. 4

   Pull the plunger on the top of the trap up and downwardly. Pushing the spikes in and out of the dirt will loosen the soil and make the trap more efficient. Pull up and down on the plunger on the top of the trap several times until the soil is loose.^[13]

   • Keep hands and anxiety away from the bottom of the trap or you may injure yourself.

5. v

   Pull up on the plunger until the trap snaps into place. Once you pull the plunger enough, the trap latch should snap deeply onto the trigger pan.Your trap is at present fix. The next time a mole tries to burrow through the dirt, the spikes will spring down into the dirt where the mole is.^[14]

   • Keep children and pets out of the chiliad when the mole trap is engaged.

Advertizing

Add New Question

• Question

  Where do yous set mole traps?

  

  Elmer Bensinger is a Pest Control Specialist with Eden Advanced Pest Technologies in Spokane, Washington. With over 20 years of feel, Elmer specializes in integrated pest management and products such as insecticides and rodenticides. He studied business at South Puget Sound Customs College.

  

  Pest Control Specialist

  Skilful Answer

  Information technology depends on the style of trap you're using, just they typically either get in the mole hill, on top of information technology, or right next to it. In either case, you're going to need to figure out where the mole really is before you fix the trap.

• Question

  What's the most effective mole trap?

  

  Elmer Bensinger is a Pest Control Specialist with Eden Advanced Pest Technologies in Spokane, Washington. With over 20 years of experience, Elmer specializes in integrated pest direction and products such every bit insecticides and rodenticides. He studied business organisation at Due south Puget Sound Community College.

  

  Pest Command Specialist

  Proficient Answer

  The hook-style traps that beat the mole are the nigh effective. Unfortunately, the live traps aren't nearly as effective equally those claw traps.

• Question

  What tin can I use instead of a trap?

  

  Elmer Bensinger is a Pest Command Specialist with Eden Advanced Pest Technologies in Spokane, Washington. With over twenty years of experience, Elmer specializes in integrated pest management and products such as insecticides and rodenticides. He studied business at South Puget Sound Community Higher.

  

  Pest Control Specialist

  Expert Respond

  There are machines you can buy that will pump the mole'southward tunnel with carbon dioxide to put it down. Those are fairly effective. The mole won't feel any hurting either, if that'south something you're worried virtually. It will merely go to sleep and dice quietly.

• Question

  Is in that location a fashion to increase the sensitivity of the force per unit area plate in the victor headset mole trap?

  

  Hobie Punch

  Customs Answer

  To improve sensitivity, cut a 1 X 1-1/4-inch rectangular shim out of a 1/16th-inch thick piece of difficult plastic and glue it inside and at the finish of the 1-1/4-inch-wide iron channel that has the xanthous label. The shim prevents the cocking mechanism from rotating every bit far past the triggering bespeak when the trap is gear up.

Enquire a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertisement

Video

Things Yous'll Need

• Gardening spade
• Mole trap

Nigh This Article

Thanks to all authors for creating a page that has been read 32,722 times.

Did this article help you?

Source: https://www.wikihow.com/Set-a-Victor-Mole-Trap

Share this post